3dprinterji/config ender.txt

49 lines
1.9 KiB
Plaintext

Recv: T:14.17 /0.00 B:14.51 /0.00 @:0 B@:0
Send: M503
Recv: echo: G21 ; Units in mm (mm)
Recv:
Recv: echo:; Filament settings: Disabled
Recv: echo: M200 S0 D1.75
Recv: echo:; Steps per unit:
Recv: echo: M92 X80.00 Y80.00 Z400.00 E404.00
Recv: echo:; Maximum feedrates (units/s):
Recv: echo: M203 X500.00 Y500.00 Z10.00 E60.00
Recv: echo:; Maximum Acceleration (units/s2):
Recv: echo: M201 X500.00 Y500.00 Z100.00 E5000.00
Recv: echo:; Acceleration (units/s2): P<print_accel> R<retract_accel> T<travel_accel>
Recv: echo: M204 P500.00 R1000.00 T500.00
Recv: echo:; Advanced: B<min_segment_time_us> S<min_feedrate> T<min_travel_feedrate> X<max_x_jerk> Y<max_y_jerk> Z<max_z_jerk> E<max_e_jerk>
Recv: echo: M205 B20000.00 S0.00 T0.00 X8.00 Y8.00 Z0.40 E5.00
Recv: echo:; Home offset:
Recv: echo: M206 X0.00 Y0.00 Z0.00
Recv: echo:; Auto Bed Leveling:
Recv: echo: M420 S0 Z10.00
Recv: echo: G29 W I0 J0 Z0.90850
Recv: echo: G29 W I1 J0 Z0.01000
Recv: echo: G29 W I2 J0 Z-0.80900
Recv: echo: G29 W I0 J1 Z1.01550
Recv: echo: G29 W I1 J1 Z-0.01900
Recv: echo: G29 W I2 J1 Z-0.82850
Recv: echo: G29 W I0 J2 Z1.06300
Recv: echo: G29 W I1 J2 Z0.11700
Recv: echo: G29 W I2 J2 Z-0.67550
Recv: echo:; Material heatup parameters:
Recv: echo: M145 S0 H150.00 B45.00 F255
Recv: echo: M145 S1 H190.00 B55.00 F255
Recv: echo: M145 S2 H240.00 B70.00 F255
Recv: echo: M145 S3 H220.00 B85.00 F255
Recv: echo:; PID settings:
Recv: echo: M301 P28.72 I2.62 D78.81
Recv: echo: M304 P462.10 I85.47 D624.59
Recv: echo:; LCD Brightness:
Recv: echo: M251 B255
Recv: echo:; Power-Loss Recovery:
Recv: echo: M413 S0
Recv: echo:; Z-Probe Offset (mm):
Recv: echo: M851 X-43.60 Y-10.00 Z0.14
Recv: echo:; Filament load/unload lengths:
Recv: echo: M603 L0.00 U0.00
Recv: echo:; Filament runout sensor:
Recv: echo: M412 S0 D0.00
Recv: ok
Recv: T:14.27 /0.00 B:14.45 /0.00 @:0 B@:0